I picked up a Hewlett-Packard 3457A digital multimeter. This is professional quality test equipment and it places the lab into a new league of measurement capability.
HP 3457A DMM
Laboratory Grade Equipment
I have been on the web researching metrology quality meters for the past few months. So, when I saw this unit, I had to get it. I paid a little bit more than usual for this than for my other equipment, but it is still a bargain price for laboratory grade equipment.
The 3457A came to market in 1986. The chassis is wide and designed to fit in an equipment rack. It’s not very tall and it’s not very deep, so it fits nicely on my shelf.
So Many Buttons
The 3457A is a 6.5 digit multimeter that can measure everything that I would need to measure in any of my projects. It has one of the greatest number of buttons of any piece of equipment past or present. There are 42 front panel buttons, not including the power button, and all but a couple the buttons have a secondary function. That is a lot of buttons.
So Many Digits
At 6.5 digits, the display can show a full six digits to the right of the decimal point. That’s a lot of digits. 1 The number of digits is not always a good measure of the capability of a meter. Along with the number of digits displayed, the accuracy and resolution of a meter is also determined by the number of “counts” 2.
3457A with 6 digits
Best of all, this 3457A, and all other HP equipment, has a computer interface, HP-IB.3 Granted, it’s not modern ethernet wi-fi, but it has computer control capability to enable laboratory automation.
Laboratory automation, that’s my goal.
Since, there is so much to talk about with this DMM, I will save it for a dedicated page later on. But for now, I have to go play with this thing.
6.5 digits is a measurement sensitivity down to 100 nanovolts. [↩]
Fluke Blog Digital Multimeters: “What is the difference between counts and digits?” [↩]
Hewlett-Packard-Interface Bus, HP-IB, or now called General Purpose-Interface Bus, GP-IB [↩]
My Fluke 101 handheld multimeter makes the basic measurements, except for current. To remedy this metrology1 void, I needed to get a multimeter that can measure current. I got very lucky and found these two Keithley bench top DMMs. The EBay seller was eager to sell these two units and I managed capture both units for $60. They even came with power cords, which is a very nice surprise.
The Kethley 197 is a bench top 5 1/2 digit digital multimeter that measures AC and DC voltage, AC and DC current, resistance, and includes a diode tester.
Here are a couple links from a couple other Keithley 197 owners. A teardown and a repair.
Keithley AN-USM-486A DMMs
Honorably Discharged from the U.S. Army
The DMMs safely arrived and I noticed that they had stickers indicating that these instruments were owned by the U.S. Army. They had calibrations stickers dating to the mid-1990s. I think the EBay seller likely acquired these units from a government auction.
The front panel labels this model as a Keithley 197 Autoranging Microvolt DMM, but on the bottom of the chassis, there is a label identifying this model as a AN-USM-486A. Apparently, Keithley made special models of the their 197 DMM specially for the US military.
A Few Differences
This military version of the 197 DMM is identical to the standard Keithley 197 except for a few differences.
The AN-USM-486A does not have a backlight LCD display. The civilian Keithley 197 includes a backlight illuminating the LCD.
The AN-USM-486A has a detachable power cord. The normal 197 has a permanently mounted unremovable power cord at the rear of the unit.
The AN-USM-486A has additional electro-magnetic shielding and extra toroidal filters within the chassis. The normal model 197 does not have these additions.
Aside from these differences, the AN-USM-486A is the same as the normal Keithley 197 DMM. There is even a data logging feature that can store up to 100 measurements.
It Needed Some Cleaning
The two DMMs work well and they seem to have both held their calibration over the decades.
The soft buttons on the top left of the front panel were sometimes unresponsive and the LCD display would sometimes not show their digits completely. Since a layer of light brown dust coated both units, perhaps the buttons and LEDs just needed a good cleaning.
The Kethley 197 service manual is available on the internet and it provides detailed instructions to disassemble the DMM. The manual is well written and comes with full schematics.
The service manual instructions were clear and easy to follow. I took apart and gave the chassis a good cleaning with compressed air. I disassembled the front panel and cleaned the contacts of the soft buttons with some fine grit sandpaper. The LED display was also easy to disassemble and I cleaned the contacts with some isopropyl alcohol. After I put it all back together, everything worked.
I can now measure current with the twin DMMs.
Metrology is the scientific study of measurement. [↩]
My new function generator has arrived. It’s a BK Precision 3011B that I found on EBay for $20. This instrument dates to the early 1990s. 1 The previous owner was a Ham Radio Operator and he kept it in nice looking condition. The front panel is a bit worn, the background bleached and faded. But it works.
BK Precision 3011B
A Basic Function Generator
The 3011B is a basic function generator and it only generates waveforms as high as 2 MHz. Good for low frequency and audio projects.
There is not that much to this generator. It produces sine, square, and triangle waveforms, and it generates TTL and CMOS pulse waveforms which are useful for digital projects. The frequency readout has a large red four digit LED display.
It Works!
Here is the 3011B delivering a 10 KHz sine wave to my Kenwood Oscilloscope.
BK 3011B 10 KHz
As you can see above, the LED display is nice and bright. But the LED background is a bit too reflective, and the unlit elements of the LED are much too visible. This makes the display hard to read unless it is dark with the lights off in the lab.
The LED display has two decimal digit resolution. And, the frequency counter reads a little bit high, so it needs calibration. I’m not sure if it even can be calibrated.
The output voltage goes as high as 10V with a 50 ohm load. However, the minimum output voltage does not go all the way to zero volts. The lowest that it will go is about 1.5V. I don’t know if this is by design or by defect, and the specifications do not state a minimum output voltage value. This will be a problem if I want to do low voltage measurements. I plan to do measurements that require signal amplitudes of 0.22 volts (or 0.0 dBm at 50 ohms, which I will explain in future posts) and much much lower. Clearly, this is not the instrument to use for those measurements.
Is that Distortion I see?
Reducing the output from the generator and increasing the timebase resolution on the oscilloscope reveals greater detail on the waveform. The 3011B emits a very unclean signal. As you can see below, there is a slight defect in the waveform to the right of the maximum peak and a very jagged defect just after the minimum peak is reached. I begin to see this distortion at frequencies greater than 5 KHz and it just gets more pronounced at higher frequencies up to the 2MHz maximum. There is definitely some problem in the circuit causing this distortion.
A brief search engine query revealed another BK 3011B owner who has a very similar sine wave distortion on his unit. Here is his YouTube Video. 2 Although the distortions he is seeing are not exactly the same as seen on my generator, they are very similar and they are positioned in the same places on the sine wave as shown on my 3011B. Actually, his distortions look quite worse than what I am seeing on my generator. This seems to be a systemic problem that is common to the 3011B. 3
Yet, It’s Still Useful
The square wave and triangle waveforms also show the similar defect as seen in the sine wave. However, this generator is still useful for producing TTL and CMOS square waves for digital circuits.
Even though the waveform is distorted, output voltage doesn’t go very low, and the LEDs are hard to read. I can’t complain about the price and the instruction and service manual are available on the internet.
It’s good for very quick and crude measurements.
The instruction manual has a copyright date of 1992. [↩]
The fellow with this similar problem tried fixing it but he could not find a solution to the problem. [↩]
In my opinion, it’s likely a problem within the BK 3011B waveform generation circuit. [↩]
An oscilloscope is the central piece of equipment in any electronics workbench. You use it to see and measure how electrical voltage varies over time.
The oscilloscope, or “scope”, produces a two-dimensional graphical display of a waveform. It displays voltage along the vertical axis and time along the horizontal axis. Scopes can display one or more waveforms on the screen, one for each input channel.
The older oscilloscopes are typically analog, non-computerized, scopes and display signals and waveforms in real-time. What you see is what you just measured.
Modern digital oscilloscopes have huge memory capacities. They display, measure, and record waveforms that can be played back and analyzed in great detail.
My New Old Scope
Scopes are expensive, but you can get a great deal if you settle for an older analog oscilloscope. I found this great little old analog scope on EBay for $50.
Kenwood CS-5400 Oscilloscope
My new old scope is the Kenwood CS-5400, a 3-channel, 100 MHz bandwidth analog oscilloscope. This scope is from the 1980s and made in Japan. It’s called a “Readout Oscilloscope” because you can read the measurements directly on the screen. Traditionally, the user had to visually look at the waveform on the grid and make measurements visually by eye. A screen readout was quite a fancy feature to have in its time. Considering that this scope is purely analog a direct screen read out is quite impressive. It is completely non-digital without a CPU or microcontroller under the hood.
Until now, I didn’t know that Kenwood, a Japanese company, made electronic test equipment or oscilloscopes. I was only familiar with Kenwood’s other products of ham radio and stereo audio systems. The big names in oscilloscopes are typically Tektronix, Hewlett-Packard was Agilent now Keysight, Rhode-Schwarz, and more lately Rigol and Siglent. But Kenwood is unknown for test equipment in North America. But apparently, Kenwood (now Texio-Kenwood) is quite prominent in Asia, particularly in Japan.
It Works!
The Kenwood arrived from the seller nicely and safely packed and in good condition. Its only defect is that it’s missing a rubber foot on the front corner. It came alive when I turned it on. I plugged in a set of cheap oscilloscope probes and a power cord and I was in the oscilloscope business.
The first thing I did was to connect the probes to the calibration output. This output emits a fixed 1 KHz square wave so you can test your basic measurements and calibrate your scope probes (called Probe Compensation.) The screen readout said exactly 999.99 Hz at 1.01 volt peak-to-peak. Close enough, I was very happy.
Unfortunately, the scope did not come with an operating or service manual. In fact, I could not find any manuals for this scope on the internet either. So, if this scope breaks I would have to fix it blind.
Every electronic project requires electrical power. Generally, electrical circuits need a supply of direct current (DC) electricity to operate. The energy source can be as simple as a battery, but we normally need a source of energy that lasts longer and can deliver much more energy at a much greater rate than a simple battery. Because the electricity coming out of the power outlets is alternating current (AC) our electronics circuits cannot make use of the electricity directly out of our power outlets. Thus, the need for a Power Supply.
What does a power supply do?
A power supply is a device that converts AC to DC electrical power1. But a power supply does much more than just convert AC to DC. A power supply provides an output voltage at a specific value, it delivers voltage or current at a constant, regulated, level, and can provide multiple adjustable voltages. Finally, the power supply has to be capable of delivering energy at a rate that is greater than the rate of energy consumed by the circuit that it is supplying.
So, I picked up this power supply on EBay.
Lambda LPD-421A-FM
Heavy and Rugged
These Lambda power supplies are heavy, rugged, and built like an armored tank. It is pre-owned and it’s a bit dirty, but it works. Not bad for $50 USD. There is a sticker on the back that says that the previous owner is a large company that makes copiers. This model is a dual output version and can supply power at two different voltages. Some circuits and devices need more than one voltage to operate, such as Operational Amplifiers. So having a power supply with at least one output voltage is a necessary requirement.
Each output can supply a voltage from zero to 20 Volts at a maximum of 1.7 Amperes. This translates to a maximum of 34 Watts (20V * 1.7A)2 per output. The two outputs can be connected together to get 40 Volts at 1.7 Amps for a total of 68 Watts. This Lambda is not powerful enough to power up vacuum tube circuits3. But 20 Volts is good enough for solid state projects. I will need more power supplies to do vacuum tube projects, and it would be nice to have power supplies that are programmable or computer controlled. You can never have too many power supplies.
Each output has a voltage meter and separate current meter. You set the output voltage with the Output Voltage knob. You can set the maximum output current that the power supply will deliver with the Current Limiter knob. A Current Limiter is a valuable feature and it prevents excessive current from damaging circuits.
The Specifics
Here are a few of the specifications from the Lambda product data sheet.
Lambda LPD Series Power Supply Specifications
The models in the Lambda LPD series are pretty much the same, varying only by the maximum output voltage. The specification for the LPD series states 0.01% regulation with 500 microvolts of ripple, that’s nice and constant and good enough for my projects.
I was fortunate to be able to find the instruction manual for the Lambda on the internet, because this model dates to the late 1980s. The manual is quite complete, it includes schematic diagrams and a chapter on the Theory of Operation of the power supply. An amusing option is the “fungus proofing”, a MIL-V-173 military standard anti-fungal treatment, that was available for an extra charge. I guess this military quality equipment is designed to be used anywhere in the world and under all kinds of environmental conditions.
Finally, the data sheet says that this Lambda LPD-421A-FM had a list price of $613 USD in 1980s dollars. That’s an expensive power supply even in today’s dollars, but not bad at all for $50 USD.
A circuit called a rectifier converts AC to DC and a circuit called an inverter converts DC to AC. [↩]
Finally, the first piece of equipment for the lab has arrived, a new Fluke 101 handheld digital multimeter1. It’s a very modest start, but it is just the beginning.
Basic Measurements
Fluke 101 Multimeter
Anybody who works with electricity needs a device that measures the absolute basics, a multimeter2. I wanted something simple and inexpensive but built with quality. And for fundamental electrical measurements, Fluke is one of the brands that first comes to my mind, the other being Keithley Instruments.
There are many reviews on handheld multimeters, on the EEVBlog3 and on YouTube, created by many handheld multimeter enthusiasts. I didn’t know there were so many different brands available (and I didn’t know that there were so many multimeter fanatics).
Specifications
The Fluke 101 is a simple device and it fits nicely in the palm of the hand. It measures AC and DC Voltage (up to 600 Volts CAT III)4 , AC Frequency, Resistance, and Capacitance. It also tests for electrical continuity and tests for defective Diodes as well. And it comes with a set of Fluke quality test probes with batteries included. Other competing products have more features, but for my first device, simple is better. But the Fluke 101 does not measure electrical current. So, I will have to pick up other pieces of equipment to fill that measurement deficiency.
A digital meter displays the reading in numerical digits while the more traditional analog meters display the reading with a moving needle along a printed scale [↩]
A meter is an instrument that measures some quantity, e.g. voltage. A multimeter is an instrument that measures multiple quantities, e.g. voltage, current, and resistance. [↩]
